Plastics Machinery Market In 2010 Will Increase To 14.5 Billion - Transponder Key Programmer

in Injection
Plastic Machinery is an important pillar of the development of the plastics industry, plastics industry, it offers advanced technology and equipment, its development is the basis for the development of the plastics industry, but also by the plastics industry development. From a global perspective, three main varieties of plastic machinery, followed by injection molding machine, extruder / extrusion lines and blow molding machine, plastic machinery output which accounts for more than 80%, which accounted for three types of mechanical injection molding machine combined more than half. The industry believes that these three types of plastic machinery market prospects.
Demand for high-tech injection molding machine strength
As the rapid development of injection molding machine a few years ago, and now in addition to the mainframe, the general specifications of the injection molding machine has exceeded demand and the sales will remain at the peak of the 1 / 3 of the already very good. But some high-tech injection molding machines, the market demand is gradually strengthened. First fully electric, hydraulic type injection molding machine precision. These products main market is the electronic communications, audio and video, home appliances, automobiles, processing conditions require high demands on precision injection molding machine also increased, these industries are rising industry, there is much room for growth. Second, the rapid development of hollow injection molding machine. This is because the plastic parts in the vibration of the stress destruction of all plastics in automotive applications and other large engineering problems, and a variety of rubber and plastic material with hollow injection technology combined with application, can effectively improve the defects. Third, with the aid of air, water, injection molding machine of new assistive devices. Such technologies have significant near-term market, especially the appearance of higher, long-lived products, such as home appliances, automotive, construction and other more attractive.

Lack of competitiveness of domestic extruder
Extruder applications market as the market continued to expand and technological breakthroughs, but also to maintain the overall momentum of rise slightly, but the domestic market prices fall extruder has been difficult to avoid, especially bad, and the price war has affected the domestic presses overall image and market competitiveness, but also hindered the development of plastic processing industry. The last two years, only the German company Krauss-Maffei that the arrival of transactions with China for more than 100 profile production line, plastic doors, windows and pipe processing industries most powerful enterprises to seek imports of equipment, which can not be said that the domestic manufacturer's failure. Extruder production line host and technical content of the future market will be upgrading the direction of lower prices. Host is basically made conical twin-screw extruder and single screw extruder-based, technology is relatively mature and has the largest sales market, but the general specifications of such products has exceeded demand and the market can only be maintained peak of around 50% -60%. The focus of future development of the host parallel to the twin-screw extruder different for a large amount of extrusion molding extrusion. Parallel twin screw extruder to the sixth and seventh-generation high-speed, large aspect ratio direction. Single screw extruder is the development direction of large diameter, large aspect ratio, exhaust and smooth. In fact, the single-screw extruder is a low-power, low-cost model, as long as the technology properly, it can basically achieve the performance of twin-screw extruder, such as the United States is now used on most of the plastic extrusion machine is a single screw, due to high technology to replace the twin-screw extruder.

Blow molding machine has the most development potential
Blow molding equipment for lower prices (about 1/3-1/2 injection) and low energy consumption (injection molding, the mold cavity pressure for the 15-140MPa, while the wind blow when the parison inflation pressure is generally less than 1MPa), adaptability (can be formed complex, double-wall of the workpiece), which make up the shortcomings of injection molding, molding of industrial workpieces with a high degree of integrity, good overall performance and high added value, cost lower. Thus, while the current blow molding machinery in the three lowest proportion of presses, but in the future will maintain strong momentum, is the fastest growing, and the most promising models. Plastics industry in China ,2000-2005 long-term planning for plastic products, the average annual growth rate of about 10% ,2006-2015 annual growth rate of 8%. By 2005 the production of plastic products will reach 25 million tons, plastic products output in 2015 is expected to double to 50 million tons. Plastics processing industry will continue to be good prospects for the development of plastic machinery manufacturing industry in China driving force behind the rapid development, projected 2001-2010, China's demand for plastic machinery 6% average annual growth rate is estimated as 14.5 billion by 2010 .
Author Box
gaga has 1 articles online

I am an expert from, while we provides the quality product, such as transponder key programmer Manufacturer , laser key cutting machine Manufacturer,

Add New Comment

Plastics Machinery Market In 2010 Will Increase To 14.5 Billion - Transponder Key Programmer

Log in or Create Account to post a comment.
Security Code: Captcha Image Change Image
This article was published on 2011/01/23